Want to Fix Netgear Extender Red Light Error? Try This Out!

Want to Fix Netgear Extender Red Light Error? Try This Out!

If the red light on your Netgear extender bothering you, then don’t sweat over it! We’ve got your back! This post will guide you on how to fix Netgear extender red light issue in a fly. So, without much delay, let’s get the ball rolling!

Main Causes Behind Netgear Extender Red Light Issue

The red color LED on your Netgear WiFi range extender can degrade the performance of your device, resulting in WiFi signals dropping. Therefore, it is better to know the exact reasons behind the Netgear extender red light issue.

Below-mentioned are one of the most common yet major reasons causing the issue. Keep scrolling down!

  • Your Netgear extender is placed in a congested, or non-ventilated area. Or, near to interference-creating WiFi devices. Due to this, you will not be able to receive the extender’s WiFi signals to the fullest.

  • Partial or improper Netgear WiFi extender setup can also lead you to the issue.
  • In the event that there are multiple devices connected to the extender’s SSID, your device will not be able to connect to your exiting router. As a result, you will see red color LED on your Netgear WiFi range extender.

  • Outdated firmware version on your Netgear extender also results in the issue.

  • Internet connection dropping frequently.

  • Issues from your ISP end.

That’s all! These were some of the basic reasons why you are seeing red light on your Netgear WiFi range extender. Now, let’s get to know the troubleshooting steps to get rid of the issue in no time. Keep scrolling down!

Fixed: Netgear Extender Red Light Issue

The Power Supply

Make sure that your Netgear WiFi range extender is getting continuous and uninterrupted power supply from its wall outlet. Also, the wall plug you are about to use to plug in your Netgear extender must not be damaged.

Note: Do not use a power extension to plug in your Netgear extender.

Relocate Your Netgear Extender

To get the most out of your Netgear extender, it is suggested to place it on a higher surface and at a ventilated location. Do not hide your extender. Apart from that, to avoid any kind of WiFi-signal interruption, do not place your Netgear extender too closer to router.

Update the Extender’s Firmware

An outdated firmware version on your Netgear extender may also result in the issue. Thus, to prevent red light error on your device, ensure that the firmware version on it is up-to-date. To update extender’s firmware and to check whether the latest version is downloaded and installed on your device, visit Netgear Genie setup wizard using www.mywifiext.net web address.

Bonus: To update the firmware of your Netgear extender, download and install the Nighthawk app.

Check the Connections

To deal with red light issue, ensure that the wired or wireless connection you have made between your Netgear extender, PC, laptop, router, and mobile device are proper.

Set up Your Netgear Extender Properly

In order to fix many big issues with your Netgear extender apart from the red LED one, ensure to set up Netgear extender properly. Bear in mind that a partial or wrongly performed Netgear extender setup can lead you to many big issues.

Note: Don’t know how to setup Netgear extender? Fret not! Drop us a line into the comments section.

Still getting red color LED on your Netgear extender? Power cycle your device once. Sometimes, a simple reboot or restart of the device is enough to fix Netgear extender red light issue. To restart, reboot, or power cycle your device:

  • Turn the extender off.

  • Wait for a few minutes.

  • Turn the Netgear extender on.

  • The LEDs on your device will become stable shortly after blinking.

Did the power cycling process helped you out to fix Netgear extender red light issue? No? Then which of the aforementioned fix was helpful? Do share the feedback with us.

error: Content is protected !!